Scissor device



Scissor device There are three types of scissors for water-jet looms: electric scissors, mechanical scissors and electronic scissors. One set is installed on the left and right sid…

Scissor device

There are three types of scissors for water-jet looms: electric scissors, mechanical scissors and electronic scissors. One set is installed on the left and right sides of the loom. At present, water-jet looms are mainly equipped with mechanical scissors. The scissors on the left side cut off the weft wire after each weft insertion, and the scissors on the right side clamp the CC wire to keep the cast weft wires (usually 4 to 5 wires are retained), and cut off one wire after each weft insertion. Figure 3-24 shows the mechanical scissors device.

 Adjustment of scissors
 1. Adjustment of scissor blades (Figure 3-25)
 When the scissor blades are replaced with new blades or the blades have been ground for assembly, the blades must be adjusted location between.
(1) There should be a 1mm overlap between the tips of the fixed blade 1 and the movable blade 2.
(2) There should be a gap between the rear ends of the fixed blade and the movable blade. The degree should be that nut 3 should be rotated and tightened appropriately and then locked with nut 4. The gap after locking should be 0.01~0102mm. .
2. Adjustment of the Button swing device (Figure 3-26)
Rotate the take-up handle so that the low apex of the Button swing cam 1 (the marked part of R or L) and the convex roller 2 are aligned. Adjust the side brace to a horizontal position when the On the inside of the window, the gap between the reed teeth and the movable blade 2 of the scissors is adjusted to the range of 0.5 to 1.0 mm and fixed with bolts 3.

(2) Front and rear position (Figure 3-27): Adjust with bolt 4.
① Set the position of the hour wheel to 0° (move the reed to the forward position).
② The tip of the scissor blade extends out of the reed 2mm and is fixed with bolt 4.
(3) Guide shear plate (Figure 3-28):
① Adjust the concave part of the guide shear plate 6 to be 0.5mm higher than the top of the fixed blade 1, and temporarily fix it with nut 8.
②Swing the reed 9 to the front so that the groove of the guide shear plate 6 is in the state shown in Figure 3-28, then tighten the nut 8 to fix the guide shear plate 6.
(4) The height of the scissors (Figure 3-27): Use screws 5 to adjust the upper surfaces of each part of the guide shear plate 6 to be consistent with the height of the diameter wire surface.
(5) The relationship between the overlap of the scissor blades and the scissor cam (Figure 3-29):
① Turn the loom by hand to turn the time wheel to the 40° position.
② Loosen the three screws 2 so that the center mark 5 of the scissor cam 1 meets the cam roller 3, and then tighten the three screws 2 to fix the scissor cam.
③The tips of the scissor blades will overlap by 1mm and be adjusted with the scissor connecting rod 4 (the cutting position in this state is about 10°).

(1) Position:
① The gap between the screw 3 to make the spare blade and cloth fixed into 1mm.
②Use screw 7 to set the distance between fixed blade 1 and CC guide plate to 25~30mm.
(2) Front and rear and up and down positions:
① Turn the hour wheel to 0°.
② Use screw 4 to adjust the position of the reed and scissors so that the gap between the reed and the tips of the scissors is 2mm. If the gap is too small, the blade may damage the reed swinging forward.
③ Adjust the tip of the fixed blade 1 by 0.5~1.0mm lower than the warp surface with screw 4.
(3) Overlapping amount of scissor blades:
① Turn the loom manually so that the movable blade and the fixed blade bite deeply.
② Loosen bolt 6 so that the tips of the movable blade and the fixed blade overlap by 1 to 1.5 mm, and then tighten bolt 6.
(4) Number of residual weft threads after shearing: Start the loom to introduce weft threads, and after cutting with scissors, if there are too many remaining weft threads, the overlap at the blade tip should be slightly increased. On the contrary, if it is too small, the overlap amount needs to be reduced. The standard number of remaining threads is 4 to 5.
5. Cutting angle (Figure 3-31)
Adjustment of the left scissor cutting angle:
(1) Introduce 1 weft wire into the shed.
(2) Loosen the bolt 6 of the scissors connecting rod, and turn the time wheel by hand to the angle where you want to cut the wire.
The angle when cutting is usually:
Polyester yarn is 15°±5°, Nylon yarn (Nylo) is 10°±5°
Note: Do not loosen the scissor connecting rod when adjusting The bolt 7 (the bolt 7 is pressed tightly against the finishing plane of the swing shaft).
(3) When the scissors break, tighten the bolt 6 to fix the movable blade.
(4) Introduce 1 weft thread again, manually rotate the time wheel, and try to cut the thread. It is enough to complete the thread cutting according to the set angle.
AAAE4T45UY75T

Extendedreading:https://www.alltextile.cn/product/product-7-78.html
Extendedreading:
Extendedreading:
Extendedreading:
Extendedreading:
Extendedreading:
Extendedreading:
ExtendedReading:
Extendedreading:
Extendedread

This article is from the Internet, does not represent 【www.chinagarments.com】 position, reproduced please specify the source.https://www.chinagarments.com/archives/10226

Author: clsrich

 
TOP
Home
News
Product
Application
Search